Fortinet nse5-faz-6-4 online test

Question 1

Which two methods are the most common methods to control and restrict administrative access on
FortiAnalyzer? (Choose two.)

• A. Virtual domains
• B. Administrative access profiles
• C. Trusted hosts
• D. Security Fabric

Answer:

BC

Explanation:
Reference:
https://docs2.fortinet.com/document/fortianalyzer/6.0.0/administration-
guide/219292/administrator-profiles
https://docs2.fortinet.com/document/fortianalyzer/6.0.0/administration-guide/581222/trusted-
hosts

Question 2

Which daemon is responsible for enforcing raw log file size?

• A. logfiled
• B. oftpd
• C. sqlplugind
• D. miglogd

Answer:

A

Question 3

An administrator has configured the following settings:
config system global
set log-checksum md5-auth
end
What is the significance of executing this command?

• A. This command records the log file MD5 hash value.
• B. This command records passwords in log files and encrypts them.
• C. This command encrypts log transfer between FortiAnalyzer and other devices.
• D. This command records the log file MD5 hash value and authentication code.

Answer:

D

Explanation:
Reference:
https://docs.fortinet.com/document/fortianalyzer/6.4.6/administration-
guide/410387/appendix-b-log-integrity-and-secure-log-transfer

Question 4

Which two of the following must you configure on FortiAnalyzer to email a FortiAnalyzer report
externally?
(Choose two.)

• A. Mail server
• B. Output profile
• C. SFTP server
• D. Report scheduling

Answer:

AB

Explanation:
Reference:
https://docs.fortinet.com/document/fortianalyzer/6.0.2/administration-
guide/598322/creating-output-profiles

Question 5

For which two purposes would you use the command set log checksum? (Choose two.)

• A. To help protect against man-in-the-middle attacks during log upload from FortiAnalyzer to an SFTP server
• B. To prevent log modification or tampering
• C. To encrypt log communications
• D. To send an identical set of logs to a second logging server

Answer:

A, B

Question 6

Refer to the exhibit.

What does the data point at 14:55 tell you?

• A. The received rate is almost at its maximum for this device
• B. The sqlplugind daemon is behind in log indexing by two logs
• C. Logs are being dropped
• D. Raw logs are reaching FortiAnalyzer faster than they can be indexed

Answer:

D

Question 7

You are using RAID with a FortiAnalyzer that supports software RAID, and one of the hard disks on
FortiAnalyzer has failed.
What is the recommended method to replace the disk?

• A. Shut down FortiAnalyzer and then replace the disk
• B. Downgrade your RAID level, replace the disk, and then upgrade your RAID level
• C. Clear all RAID alarms and replace the disk while FortiAnalyzer is still running
• D. Perform a hot swap

Answer:

A

Explanation:

https://community.fortinet.com/t5/FortiAnalyzer/Technical-Note-How-to-swap-Hard-Disk-on-
FortiAnalyzer/ta-
p/194997?externalID=FD41397#:~:text=If%20a%20hard%20disk%20on,process%20known%20as%20
hot%20swapping

Question 8

On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

• A. FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
• B. FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
• C. FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
• D. FortiAnalyzer is functioning normally

Answer:

C

Explanation:
Reference:
https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/4cb0dce6-
dbef-11e9
-
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)

Question 9

In the FortiAnalyzer FortiView, source and destination IP addresses from FortiGate devices are not
resolving to a hostname.
How can you resolve the source and destination IP addresses, without introducing any additional
performance impact to FortiAnalyzer?

• A. Resolve IP addresses on a per-ADOM basis to reduce delay on FortiView while IPs resolve
• B. Configure # set resolve-ip enable in the system FortiView settings
• C. Configure local DNS servers on FortiAnalyzer
• D. Resolve IP addresses on FortiGate

Answer:

D

Explanation:
https://packetplant.com/fortigate-and-fortianalyzer-resolve-source-and-destination-ip/
As a best practice, it is recommended to resolve IPs on the FortiGate end. This is because you get
both source and destination, and it offloads the work from FortiAnalyzer. On FortiAnalyzer, this IP
resolution does destination IPs only

Question 10

You have recently grouped multiple FortiGate devices into a single ADOM. System Settings > Storage
Info
shows the quota used.
What does the disk quota refer to?

• A. The maximum disk utilization for each device in the ADOM
• B. The maximum disk utilization for the FortiAnalyzer model
• C. The maximum disk utilization for the ADOM type
• D. The maximum disk utilization for all devices in the ADOM

Answer:

D